ELVEFLOW Sensor Reader V3

Buy ELVEFLOW products from MSE Supplies at the best value.

Product Description

USB Microfluidic Sensor Reader

Can host up to 4 Elveflow Microfluidic Flow Sensors

Pressure Sensor and Bubble detector

Elveflow® Smart Interface software included

Monitor the Measurement of all Your Microfluidic Sensors

Connect pressure and flow sensors wherever you want in the setup to closely monitor your microfluidic experiment.

The Sensor Reader module allows you to control 4 sensors simultaneously. Additionally, our software allows controlling several Sensor Readers simultaneously.

The MSR is the ideal supplement to the OB1 flow controller should you need high control over your experimental parameters.

Sensor Reader also allows you to use third-party sensors.

Fast and Precise

With an acquisition sampling rate of up to 200 Hz and an 16 bit resolution, the Sensor Reader allows you to easily conduct experiments involving monitoring or controlling a physical parameter with analog and digital sensors in real time.

Wide Sensors Compatibility

See Elveflow® fully compatible pressure sensor & flow sensor below.

Noise Reduction

An embedded analog 60 Hz low pass filter function can be activated on each channel independently to reduce sensor noise.

Performance

Our Sensor Reader achieves an 16 bits resolution at up to 200 Hz sampling rate and a sub-resolution noise, for accuracy levels on your sensor measurements down to 0.05% of the full scale and a response time down to 5 ms.

Sampling rate up to 200 Hz
Resolution :from 9 to 16 bits
Input range : 0 – 10 V
Fully compatible with other Elveflow instruments
Measurement noise below resolution
Noise reduction function with a 3rd order 60 Hz low-pass filter

Elveflow® Pressure & Flow Sensors – Fully Compatible

We have already selected a wide range of integrated sensors fitting microfluidic applications.

Flow Sensors (MFS)

Resolution 1,5 pL/sec
Ranges from 0.07 to 5000 μL/min

Pressure Sensor (MPS & MFP)

Accuracy down to 0.2 % of Full Scale
4 ranges from 5 psi (340 mBar) to 100 psi (7 bar)

All our sensors are provided with an M8 electrical connection and can be used with the Sensor Reader. We also provide all the microfluidic connector kits necessary to start your experiment.

1. Elveflow’s Single Software (ESI)

Monitor and automate your setup using our ESI software that allows you to measure, control and automate your experiment using only one interface.

2. Flow Sensor (MFS) or Pressure Sensor (MPS)

Place the sensors anywhere you want on your fluidic path and electrically connect your sensors to the Microfluidic Sensor Reader.

Thanks to their small footprint, sensors can be placed anywhere within your fluidic system.

3. Microfluidic Sensor Reader (MSR)

Connect the sensor reader to your computer via USB and monitor it using the Elveflow® Smart Interface

4. Chip / Capillary

Add you chip to complete the standard setup. In this position, the sensor directly measures the pressure entering the microfluidic chip. You can add another pressure sensor at the chip outlet in order to get the difference in pressure and/or the microfluidic resistance.

Specifications

The following table summarizes the main features of the Elveflow® MSR Microfluidic Sensor Reader.

SENSOR READER UNIT	SPECIFICATIONS
Number of sensors connections	up to 4
Sensor connectors	M8 female (4 pins)
USB reading current min – max	200 mA – 800 mA
Sensor power supplies voltage (2 power supplies tunable independently each of which feeding 2 sensors)	5 – 24 V
Max total power on the 4 channels	0.9 W
SENSOR INPUTS
Impedance	1 MΩ
Acquisition frequency	200 Hz
Acquisition resolution	from 9 to 16 bits
Input range	0- 10 V
Resolution (1 bit)	5 mV
Noise (full band)	5 mV rms
Compatible sensors	Elveflow MFS flow sensor, MPS pressure sensor, MFP FlowPlus pressure sensor, MBD bubble detector, other sensors

Non-contractual information, may be changed without notice

Sensor Reader Size: without connectors (length x width x height): 91 x 69 x 29 mm

Weight: 320 g

This product has been added to the cart.